You need a Safe Work Method Statement (SWMS) for plumbing work that is construction work and falls into a high risk construction work (HRCW) category. For plumbers, the categories that come up most are trenches deeper than 1.5 metres, confined spaces such as pits and tanks, work on or near pressurised gas mains or piping, work near energised electrical services, falls of more than 2 metres, and areas where powered mobile plant is moving.
Not every plumbing job is construction work. Minor testing, maintenance or repair work on a structure is excluded, so some small service calls fall outside the SWMS rules altogether. This guide matches common plumbing tasks to the categories, then covers what the SWMS must say.
For the general test, see do I need a SWMS?. For the full list, see high risk construction work: the 18 categories.
When is plumbing construction work?
Construction work includes work carried out in connection with the construction, alteration, renovation, repair, maintenance or refurbishment of a structure, and the installation, testing or maintenance of an essential service in relation to a structure (regulation 289 of the model Work Health and Safety (WHS) Regulations; section 289 of Queensland's WHS Regulation 2011). Minor testing, maintenance or repair work on a structure is excluded (r 289(3)(d)).
So a new drainage installation or a bathroom renovation is construction work. Replacing a tap washer on a service call is likely to be minor repair work. In between, look at the scale of the job and what it involves, and remember the general duty to manage risks applies either way.
Which high risk construction work categories matter for plumbing?
The model WHS Regulations list 18 categories in regulation 291 (section 291 in Queensland). The ones plumbers hit most are construction work that:
- is carried out in or near a shaft or trench with an excavated depth greater than 1.5 metres, or a tunnel
- is carried out in or near a confined space
- is carried out on or near pressurised gas distribution mains or piping
- is carried out on or near chemical, fuel or refrigerant lines
- is carried out on or near energised electrical installations or services
- is carried out in an area that may have a contaminated or flammable atmosphere
- involves a risk of a person falling more than 2 metres
- is carried out in an area at a workplace in which there is any movement of powered mobile plant
- is carried out on, in or adjacent to a road, railway or other traffic corridor in use by traffic other than pedestrians
- involves, or is likely to involve, the disturbance of asbestos.
Common plumbing jobs and the categories they often trigger
This is a guide, not a ruling. Depth, location, services and the plant on site decide which categories apply.
| Plumbing task | Often triggers | Note |
|---|---|---|
| Sewer and stormwater drainage in trenches | Trench over 1.5 m; powered mobile plant | Trench support and services location belong in the SWMS. |
| Work in pits, manholes, tanks or risers | Confined space; contaminated or flammable atmosphere | Entry needs a confined space entry permit. |
| Gas fitting near live supply | Pressurised gas distribution mains or piping | Isolation, purging and testing steps in the method. |
| Roof plumbing, gutters and downpipes | Falls over 2 m | Edge protection or scaffold before anyone goes up. |
| Suspended pipework in commercial buildings | Falls over 2 m; powered mobile plant (elevating work platforms) | The access method and who is licensed to use it. |
| Road openings for connections | Traffic corridor; trench; powered mobile plant | A traffic plan may also be needed. |
| Drain inspection, jetting and relining | Confined space; contaminated atmosphere | Gas testing and ventilation before entry. |
| Renovations in older homes | Possibly asbestos; energised electrical services | Older pipes, flues and sheeting can contain asbestos. |
| Tap washer or minor leak repair | Often not construction work | The general duty to manage risk still applies. |
What must a plumbing SWMS cover?
Regulation 299 of the model WHS Regulations (section 299 in Queensland) says a SWMS must:
- identify the work that is high risk construction work
- state the hazards relating to that work and the risks to health and safety associated with those hazards
- describe the measures to be implemented to control the risks
- describe how the control measures are to be implemented, monitored and reviewed.
It must take into account the circumstances at the workplace and, on a construction project, the principal contractor's WHS management plan, and be readily accessible and understandable to the people who use it.
For plumbing, that usually means the SWMS sets out:
- the trench depth, ground conditions and the support method (shoring, benching or battering)
- the underground services information obtained and how services were located on site
- whether any space is a confined space, and the entry permit, atmospheric testing, standby person and rescue arrangements
- how gas, water and electrical supplies are isolated, tested and made safe
- the access method for work at height, and the edge protection
- how plant movements are separated from people
- how sewage, chemicals and contaminated water are handled
- who supervises, and how the controls will be checked.
Workplace Health and Safety Queensland (WHSQ) says statements such as "use appropriate PPE" (personal protective equipment) do not detail the control measures. Name the control you will use.
What sits beside the plumbing SWMS?
Trenches. For a trench at least 1.5 metres deep, all sides must be adequately supported by shoring, benching or battering, unless a geotechnical engineer gives written advice that they are safe from collapse, and the area must be secured from unauthorised access (regulation 306; section 306 in Queensland). The person with management or control of the workplace must obtain current underground essential services information before excavation starts (regulation 304). See excavation and trenching SWMS.
Confined spaces. A worker cannot be directed to enter a confined space without a confined space entry permit completed by a competent person (regulation 67; section 67 in Queensland). See confined space entry and rescue.
Asbestos. Disturbing asbestos is a high risk construction work category, and removal has its own licensing rules. See asbestos removal SWMS and licences.
Airborne contaminants. Sewer gases, solvent cements and fumes from hot work are airborne contaminants. From 1 December 2026, workplace exposure limits (WEL) replace the workplace exposure standards (WES); Safe Work Australia says persons conducting a business or undertaking (PCBUs) must comply with the WES list up to and including 30 November 2026, and with the WEL list from 1 December 2026. Check each product's safety data sheet (SDS). See what are WES and WEL?.
Trade licences. Plumbing and gasfitting licences are issued under separate state laws. The SWMS does not replace them.
Plant procedures. Drain jetters, pipe threaders, core drills and fusion welders are better covered by safe operating procedures (SOPs) beside the SWMS.
What is in the Plumbing pack?
The Plumbing SWMS Trade Pack has 24 SWMS: one Plumbing Master SWMS and 23 task SWMS:
- Site Establishment & Setout
- Manual Handling
- Material Handling, Loading & Unloading
- Truck Operations & Deliveries
- Excavation & Trenching (incl. Near Assets)
- Trenchless Works (Boring & Pipe Jacking)
- Underground Drainage
- Rough-in & Final Fit-out
- Mechanical & Suspended Pipework
- Pump & Valve Installation
- Gas Fitting
- Poly Pipe Welding (Electrofusion and Butt Fusion)
- Drain Inspection & Cleaning (CCTV, Jetting, Re-lining, Disinfecting)
- Concrete Chasing
- Confined Space Work
- Risers - Working In
- Working at Heights - EWP Operations (elevating work platform)
- Temporary Services Connection
- Wastewater Reclamation Unit
- Hazardous Substances
- Plumbing Call-out
- Working in Private Residences
- Pipe Relining (CIPP)
The pack comes in editable Word with a free pack of 30 safe operating procedures (SOPs). Each state edition references that state's Act and regulator.
What still has to be tailored?
Before the SWMS goes to site, add:
- the site address, the builder and the date
- the trench depths, ground conditions and support for this job
- the services located and how
- any confined spaces, and the permit and rescue arrangements
- the isolation points for gas, water and power
- the access equipment and the operators' licences
- who supervises, and the crew's sign-on after you have talked it through with them.
See how to use a SWMS template and keeping, signing and reviewing a SWMS.
Victoria and other states
Victoria uses the Occupational Health and Safety (OHS) Regulations 2017, made under the OHS Act 2004. Its 19 types of high risk construction work include work involving a confined space, a trench or shaft deeper than 1.5 metres, work on or near pressurised gas distribution mains or piping, and work on or near chemical, fuel or refrigerant lines (regulation 322). Victoria's definition of construction work includes the installation, testing and maintenance of gas, water, sewerage, electricity or telecommunications services in or of any building or structure, and excludes routine or minor testing, maintenance or repair work (regulation 321). Victoria also requires notice to WorkSafe Victoria before some trench, shaft and tunnel work (regulation 355).
The other states and territories have adopted the model WHS Regulations in their own laws. See SWMS requirements by state.
Common questions
Do plumbers need a SWMS?
A plumber needs a Safe Work Method Statement (SWMS) when the job is construction work in a high risk construction work category, such as a trench deeper than 1.5 metres, a confined space, work near pressurised gas mains or piping, or a fall of more than 2 metres. Many builders ask for a SWMS from every trade anyway.
Does a small plumbing repair need a SWMS?
Often not. Minor testing, maintenance or repair work on a structure is excluded from construction work under the model WHS Regulations (r 289(3)(d)), and Victoria has a similar exclusion. You still have to manage the risks of the job.
Is gas fitting high risk construction work?
Construction work carried out on or near pressurised gas distribution mains or piping is a high risk construction work category. Whether a particular gas job falls within it depends on the work and where it is done. Gasfitting licences are a separate requirement under state law.
Do I need a confined space permit to work in a pit?
If the pit is a confined space, a worker cannot be directed to enter it without a confined space entry permit completed by a competent person. Not every pit is a confined space, so check it against the definition and record the decision.
Is the list different in Victoria?
Victoria uses its own OHS Regulations 2017 and lists 19 types of high risk construction work. The plumbing-related categories are similar but worded separately, so check WorkSafe Victoria's list for work in Victoria.
Sources: Work Health and Safety Regulation 2011 (Qld), sections 67, 289, 291, 299, 304 and 306, Model WHS Regulations numbering, Occupational Health and Safety Regulations 2017 (Vic), Authorised Version No. 018 (as at 20 October 2026), regulations 321, 322 and 355, Safe Work Australia, Workplace Exposure Limits for airborne contaminants and Workplace Health and Safety Queensland, Safe work method statements.
Start from a proper SWMS, not a blank page
State-specific, editable templates written for your state. Download instantly, then make it yours for the job and the site.
This guide is general information, not legal or safety advice, and does not guarantee compliance. Laws and site conditions vary, so always check your state regulator and have documents reviewed by a competent person.
