Workplace Exposure Standards (WES) are the legal upper limits for dusts, fumes, mists, gases and vapours in a worker’s breathing zone. From 1 December 2026 they become Workplace Exposure Limits (WEL), once each jurisdiction has put the new list into its work health and safety laws. Until then, the WES still apply.
For a trade business, this is a good time to check what your crews breathe in, whether the controls work, and whether your documents still quote the right numbers.
What is an exposure standard?
An exposure standard is the concentration of an airborne contaminant that a person must not be exposed to, usually measured as an average over an eight-hour day. Under the model WHS laws, a person conducting a business or undertaking (PCBU) must make sure no one at the workplace is exposed above it.
On a trade site, the airborne contaminants that matter most are usually:
- Dusts from cutting, grinding, sanding and demolition, including silica and wood dust.
- Fumes from welding, hot work and hot bitumen.
- Mists and vapours from spray painting, solvents, adhesives and coatings.
- Gases and exhaust from plant and generators, especially in enclosed areas.
The limit is a legal ceiling, not a safe line. Safe Work Australia says the WEL is not the dividing line between a healthy and an unhealthy work environment. You still have to eliminate the risk, or reduce it as far as is reasonably practicable.
What changes on 1 December 2026?
Work health and safety ministers agreed to a harmonised transition period ending on 30 November 2026. According to Safe Work Australia:
- Until 30 November 2026, you must keep exposure below the limits in the WES list.
- From 1 December 2026, the WEL list is adopted, following implementation into the WHS laws of the Commonwealth, states and territories.
The rename itself does not add new duties. Safe Work Australia says it is there to make clear the values are limits not to be exceeded, and to match the language used overseas.
What else changes besides the name?
The list was reviewed for the first time since 2003. Most limits stayed the same, but Safe Work Australia’s summary of the changes lists:
- Changed values. Some limits went down, some went up, and some listings were added, removed, merged or renamed.
- Changed notations. The sensitiser notation is split into skin and respiratory sensitisation, a new ototoxicity notation flags substances that add to hearing loss from noise, and the carcinogen notation is removed from the list.
- 33 substances with no numeric limit. These are non-threshold genotoxic carcinogens (NTGCs), where no safe exposure level can be set. From 1 December 2026 there is no limit for them. You must eliminate them, substitute something safer, or reduce the risk as far as is reasonably practicable. They include chromium VI compounds, lead chromate, coal tar pitch volatiles, and polycyclic aromatic hydrocarbon mixtures containing benzo[a]pyrene.
Ministers also asked for more impact analysis before updating the limits for nine substances, including respirable crystalline silica, formaldehyde, benzene and hydrogen sulphide (Safe Work Australia news). Do not rely on a new figure for those until Safe Work Australia publishes one.
Look up the values themselves in the official Workplace exposure limits list, not in a summary or blog post.
Does it apply the same way everywhere?
Not exactly. The WEL become law in each place when that jurisdiction implements them, so check with your regulator.
Victoria runs its own Occupational Health and Safety Act 2004 and OHS Regulations 2017, not the model WHS laws. WorkSafe Victoria says most WEL apply there from 1 December 2026, but there is a transition to 1 December 2029 for 15 substances. Several of them matter to trades: bitumen fumes, diesel particulate matter, manganese fume and dust, Portland cement, styrene and softwood dust. Use WorkSafe Victoria’s quick reference table for the limit that applies today.
Silica also has its own rules, including the silica risk control plan. See what is a silica risk control plan.
What should a trade business do now?
- List what your work puts in the air. Go through the tasks, the products and the materials you cut, grind, spray, weld or heat.
- Check the safety data sheets (SDS) for the products you use, then check each substance against the WEL list to see whether its limit has changed.
- Check for the 33 NTGCs. If you use or create one, such as chromium VI when welding stainless steel or removing chromate coatings, plan to eliminate, substitute or minimise it.
- Review the controls. Work up the hierarchy of controls: on-tool extraction, water suppression, ventilation and enclosure come before respirators. Safe Work Australia says respiratory protective equipment can only be counted once the reasonably practicable higher-order controls are in place and the equipment is worn correctly.
- Monitor if you are unsure. If you do not know whether exposure is under the limit, air monitoring is required.
- Update your documents. Anywhere your procedures, registers or SWMS name the WES or quote a value, check them against the new list.
Where does a SWMS fit?
A Safe Work Method Statement (SWMS) is required for high risk construction work (HRCW), and one of the 18 categories is work in an area that may have a contaminated or flammable atmosphere. See the high risk construction work list and do I need a SWMS?
The SWMS sets out how the task is done and how exposure is controlled on that job: extraction, suppression, ventilation, respirators, and who checks them. It does not replace the SDS, the hazardous chemicals register, air monitoring results or health monitoring. Those records sit beside it. If the controls in your SWMS change because a limit changed, review the SWMS.
Welding has its own limit change. See welding fumes, WES/WEL and your SWMS.
Which trade packs cover fume and dust work?
These trade packs include SWMS for the dust, fume and vapour tasks in each trade, including hazardous substances. Each is $249.99 per state, editable Word, one-off purchase.
- Painting: 17 SWMS
- Welding and Fabrication: 14 SWMS
- Asbestos: 13 SWMS
- Earthmoving and Mobile Plant: 28 SWMS
Tailor each one to your products, your controls and your monitoring results before it goes to site. If you are not sure which pack fits, see which SWMS pack do I need?
Common questions
What is the difference between WES and WEL?
Workplace Exposure Limits (WEL) replace Workplace Exposure Standards (WES). Safe Work Australia says the new name makes clear the values are limits not to be exceeded and matches the language used internationally. Some individual values and notations have also changed in the review.
When do the Workplace Exposure Limits start?
From 1 December 2026, following implementation into the WHS laws of the Commonwealth, states and territories. Until then you must keep exposure below the Workplace Exposure Standards. Ask your regulator how your state has implemented the change.
Do I have to do air monitoring?
If you are not sure whether anyone is exposed above the limit, the WHS laws require air monitoring to find out. Monitoring is also how you show the controls are working.
Does my SWMS need to change on 1 December?
Review it if it names an exposure standard, quotes a value that has changed, or relies on a substance that is now a non-threshold genotoxic carcinogen. A Safe Work Method Statement (SWMS) sets out how a task is controlled; it does not replace air monitoring or the safety data sheet (SDS).
Is Victoria different?
Victoria applies most limits from 1 December 2026, but WorkSafe Victoria has a transition to 1 December 2029 for 15 substances, including bitumen fumes, diesel particulate matter, manganese, Portland cement and softwood dust. Check WorkSafe Victoria for the limits that apply now.
Sources: Safe Work Australia—Workplace Exposure Limits, Changes between the WES and WEL, WEL to apply from 1 December 2026 and WorkSafe Victoria—Workplace exposure standards and limits. General information only; check how your jurisdiction has implemented the WEL with your regulator.
Start from a proper SWMS, not a blank page
State-specific, editable templates written for your state. Download instantly, then make it yours for the job and the site.
This guide is general information, not legal or safety advice, and does not guarantee compliance. Laws and site conditions vary, so always check your state regulator and have documents reviewed by a competent person.
