Free guide

Carpentry SWMS: which tasks need one and what it must cover

Last reviewed:

You need a Safe Work Method Statement (SWMS) for any carpentry task that is high risk construction work (HRCW). For carpenters, the categories that come up most are a risk of falling more than 2 metres, structural alterations that need temporary support, load-bearing demolition, moving powered mobile plant and, in renovations, asbestos.

Plenty of carpentry is not high risk construction work at all. Hanging a door at ground level or fitting skirting inside a finished house usually is not. The same carpenter can move in and out of the categories within one day, though, so the useful question is not "does carpentry need a SWMS?" but "which of today's tasks are in the list?" This guide works through that, then sets out what a carpentry SWMS has to say.

For the general test, see do I need a SWMS?. For the full list of categories, see high risk construction work: the 18 categories.

Which high risk construction work categories matter for carpentry?

The model Work Health and Safety (WHS) Regulations list 18 categories of high risk construction work in regulation 291. New South Wales, Queensland, Western Australia, South Australia and Tasmania use the same number and the same list. The Northern Territory and the ACT also use 291 with one change each, and Victoria has its own list (see Victoria and other states below). The ones carpentry crews hit most are construction work that:

One SWMS can cover several categories, as long as it covers all of the high risk construction work in the task. Workplace Health and Safety Queensland (WHSQ) says you can prepare one SWMS for all the high risk work at a workplace or a separate SWMS for each type, and if you prepare separate ones, you need to think about how the activities affect each other.

Common carpentry jobs and the categories they often trigger

This is a guide, not a ruling. Whether a category applies depends on the site, the height, what is in the walls, and what else is moving around you.

Common carpentry jobs and the categories they often trigger
Carpentry taskOften triggersNote
Wall framing and standing framesFalls over 2 m on upper floors and at slab edges; powered mobile plant if telehandlers or cranes are movingSingle-storey frames on a ground slab may sit under 2 m, but check edges, voids and openings.
Roof trusses, including craned trussesFalls over 2 m; powered mobile plant (crane)Temporary bracing and the truss layout drawings belong in the method.
Cladding from scaffold, an elevating work platform (EWP) or trestlesFalls over 2 m; powered mobile plant if an EWP is usedRope access and swing stage work brings its own method and competencies.
Raised decks, balconies and elevated subfloorsFalls over 2 mIncludes falling off the open edge and through unfixed joists.
Stairs installationFalls over 2 m into the stairwell voidThe void needs protecting before and during the work.
Handrails and balustradesFalls over 2 mThe installer often works at the very edge that is being protected.
Renovations that remove or alter wallsStructural alterations needing temporary support; load-bearing demolition; asbestosPropping and the engineer's or builder's instructions belong in the SWMS.
Renovation work on older homes (sheeting, eaves, floor coverings)Likely disturbance of asbestosCutting, drilling or lifting material that probably contains asbestos is enough.
Fix-out inside an occupied or finished buildingOften noneIt can still pick up energised services if you are cutting into walls with live wiring.
Work in enclosed roof spacesArtificial extremes of temperature; falls through the ceilingThe model Code of Practice: Construction work gives enclosed roof cavities as an example.

Two things the table does not change. A builder or principal contractor can ask for a SWMS for work that is not high risk construction work, as a contract or site rule. And work outside the categories still has to be managed safely, even without a SWMS.

What must a carpentry SWMS cover?

The content rules are the same for every trade. Regulation 299 of the model WHS Regulations (299 in every state and territory except Victoria) says a SWMS must:

  1. identify the work that is high risk construction work
  2. state the hazards relating to that work and the risks to health and safety associated with those hazards
  3. describe the measures to be implemented to control the risks
  4. describe how the control measures are to be implemented, monitored and reviewed.

It must also be prepared taking into account the circumstances at the workplace and, on a construction project, the principal contractor's WHS management plan. And it must be set out and expressed in a way that is readily accessible and understandable to the people who use it.

For carpentry, that usually means the SWMS names the actual task (for example "erecting roof trusses on a two-storey house"), the categories it falls under, and then sets out, step by step:

Two points from the regulators are worth applying. WHSQ says statements such as "use appropriate PPE" (personal protective equipment) do not detail the control measures, so name the actual equipment. WorkSafe Victoria says listing many control options to choose from does not properly describe the measures being implemented, so pick the control you will use.

Queensland: falls controlled only by PPE or admin

Queensland adds a rule. Under section 299(4) of the WHS Regulation 2011 (Qld), if a SWMS for work with a risk of a fall of more than 2 metres relies only on administrative controls or PPE, it must describe all the control measures that were considered in reaching that decision. Queensland also sets specific fall controls for housing construction where a person could fall 3 metres or more. See SWMS in Queensland.

What sits beside the carpentry SWMS?

A SWMS covers the high risk construction work. Some things on a carpentry job need more than that.

What is in the Carpentry pack?

The Carpentry SWMS Trade Pack has 18 SWMS: one Carpentry Master SWMS and 17 task SWMS. The task SWMS are:

The pack is $249.99 per state, in editable Word, and comes with a free pack of 19 SOPs for the tools and plant carpenters use, such as the drop saw, circular saw, nail gun and EWPs. Each state edition references that state's Act and regulator.

If a builder or prequalification system is asking for your safety system as well as your SWMS, the Carpentry All-In WHS Pack puts the same SWMS inside the policies, procedures, registers and forms for the business.

What still has to be tailored?

A template gives you the tasks, hazards and controls for the trade. Before it goes to site, add:

See what to do after you download your SWMS pack, and keeping, signing and reviewing a SWMS.

Victoria and other states

Victoria lists 19 types of high risk construction work under its own Occupational Health and Safety (OHS) Regulations 2017, made under the OHS Act 2004. They are similar to the model list but worded separately, so use WorkSafe Victoria's list for work there. The other states and territories have adopted the model WHS Regulations in their own laws, with two differences worth knowing. In the Northern Territory, the falls category for residential construction work (Class 1 houses, and Class 10 buildings such as garages, carports and sheds attached or next to them) applies where a person could fall more than 3 metres; the 2 metre threshold applies to other construction work. In the ACT, section 291 adds a 19th category: processing crystalline silica material using a power tool or another mechanical method. See SWMS requirements by state.

Common questions

Does all carpentry work need a SWMS?

No. A Safe Work Method Statement (SWMS) is required for carpentry tasks that are high risk construction work, such as work with a risk of falling more than 2 metres, structural alterations needing temporary support, or work likely to disturb asbestos. Many builders still ask for a SWMS for every trade on site as a site rule.

Does truss installation need a SWMS?

Usually yes. Truss work commonly involves a risk of falling more than 2 metres, and craned trusses add the powered mobile plant category. The SWMS should cover edge protection or other fall controls, temporary bracing and how the lift is controlled.

Can one SWMS cover all my carpentry work?

One SWMS can cover several high risk construction work categories, but it has to cover all of the high risk work in the task and reflect the actual site. A master SWMS for the trade is a useful base, with task SWMS for the higher risk jobs. See master SWMS vs task SWMS.

Is building a deck high risk construction work?

It is if a person could fall more than 2 metres, which is common for raised and elevated decks. A low deck close to the ground may not be in any category, although a builder can still ask for a SWMS.

Is the list different in Victoria or other states?

Victoria uses its own Occupational Health and Safety (OHS) Regulations 2017 and lists 19 types of high risk construction work. The categories are similar but worded separately, so check WorkSafe Victoria's list for work in Victoria. Two other places differ from the model list: in the Northern Territory the falls category for houses and their garages and sheds starts at more than 3 metres, and the ACT adds processing crystalline silica material with a power tool or other mechanical method as a 19th category.

Sources: Model WHS Regulations (Safe Work Australia), regulations 5, 291 and 299 and schedule 3; the WHS Regulations of NSW, Queensland (including sections 299(4) and 306A to 306Q), WA, SA, Tasmania, the ACT (sections 291 and 418A) and the NT (regulation 291); Victoria's OHS Regulations 2017; WorkSafe Victoria; Workplace Health and Safety Queensland.

Start from a proper SWMS, not a blank page

State-specific, editable templates written for your state. Download instantly, then make it yours for the job and the site.

This guide is general information, not legal or safety advice, and does not guarantee compliance. Laws and site conditions vary, so always check your state regulator and have documents reviewed by a competent person.