A silica risk control plan is a written plan setting out how a business will control the risk from respirable crystalline silica dust on a particular job. It covers the work in front of you: what is being processed, who is exposed, what controls are in place, and how exposure is monitored and reviewed. It is one of the few project plans named directly in the WHS Regulations, which is why clients ask for it by that exact name.
Why does it exist?
Respirable crystalline silica is the fine dust released when materials containing silica are cut, ground, drilled, polished or broken. Concrete, brick, stone, tile, pavers and fibre cement all contain it. The particles are small enough to reach deep into the lungs, and the diseases they cause, including silicosis, are irreversible and can appear years after the exposure.
Australian work health and safety law responded in two steps. Engineered stone was prohibited nationally, and separately the model WHS Regulations were amended so that all crystalline silica substances, not only engineered stone, are covered. Where the processing of a crystalline silica substance is assessed as high risk, a silica risk control plan must be prepared before that work starts, and it must be kept and reviewed as the work changes.
Silica rules are not identical across Australia. Most jurisdictions work from the model Work Health and Safety Regulations and some run their own schemes, so the wording, the timing and any additional licence or notification requirement depend on where the work is. What is common to all of them is the duty to control the dust so far as is reasonably practicable, and to be able to show how. Silica law has moved quickly in recent years and continues to, so confirm the current requirement with the regulator for the state the work is in before relying on any summary, including this one.
When do you need one?
What decides it is the work itself. A plan is required where processing a crystalline silica substance is high risk, which the regulations frame around whether the work is reasonably likely to produce exposure above the workplace exposure standard, and around what a competent risk assessment concludes. Exposure standards become Workplace Exposure Limits from 1 December 2026; see what are WES and WEL?
In practice the work that raises the question most often is:
- Cutting, grinding, drilling or coring concrete, brick, block, pavers or tile
- Demolition and structural alteration of masonry and concrete
- Stonemasonry, benchtop fabrication and stone finishing
- Excavation, trenching and tunnelling in rock or silica-bearing ground
- Abrasive blasting, scabbling, road milling and surface preparation
- Dry sweeping or compressed-air cleaning of any of the above
The second trigger is commercial. A principal contractor or a prequalification portal asks for the silica plan by name before the work starts, and no amount of general dust wording in a SWMS answers it.
What goes in one?
Plans vary with the job, but a usable one covers the same ground.
- The work and the materials. What is being processed, where, for how long, and what the silica content is.
- Who is exposed. The workers doing the task and anyone nearby, including other trades and the public.
- The risk assessment. What was assessed, by whom, and what it concluded about the level of risk.
- The controls. Elimination and substitution first, then the engineering controls that do the real work: water suppression, on-tool extraction, enclosure, local exhaust ventilation. Then administrative controls and, last, respiratory protection with the fit testing behind it.
- Air monitoring. When it is done, by whom, how results are recorded and what happens when a result is high.
- Health monitoring. Who is covered, what it involves, and how records are kept and provided.
- Information, training and supervision. What workers are told and shown, and how that is recorded.
- Housekeeping and waste. How dust and slurry are cleaned up, which is where dry sweeping and compressed air get ruled out.
- Review. What triggers a review, and the record of each one.
How is it different from a SWMS?
A SWMS is written for one high-risk construction task, goes to the crew doing it, and is signed on at the job. A silica risk control plan sits a level above that. It covers the silica risk across the work, including the monitoring and health surveillance that no single task owns, and it is usually the document a client asks to see before anyone is on site.
A concrete cutting job will typically have a SWMS for the cutting and a silica plan for the dust risk across the project, and each should point at the other. A SWMS alone cannot show that air monitoring was arranged or that health monitoring records exist.
What about the other plans?
Silica is one of a set. A project usually carries several plans, each covering one aspect of the work, sitting alongside the SWMS, the SOPs and the site documents rather than replacing them. The ones most often asked for are:
- Site Emergency Response and Evacuation Plan
- Traffic, Parking and Pedestrian Management Plan
- Environmental Management Plan
- Waste Management Plan
- Hazardous Chemicals and Dangerous Goods Management Plan
- Stakeholder and Community Engagement Plan
- Asbestos Management Plan
- Erosion and Sediment Control Plan
- Noise and Vibration Management Plan
- Dust and Air Quality Management Plan
- Demolition Work Plan
- Excavation and Trenching Management Plan
- Lifting and Crane Operations Management Plan
- Working at Heights and Rescue Plan
- Confined Space Entry and Rescue Plan
- Fatigue Management Plan
- Drug and Alcohol Management Plan
- Psychosocial Risk Management Plan
- Heat and Extreme Weather Plan
- Subcontractor Management Plan
- Site Security and Access Plan
- Quality Management Plan
Which ones you need depends on the job. A road job needs traffic and dust. A demolition needs asbestos, noise and waste. A remote job needs fatigue and emergency response. Nobody needs all of them at once.
Writing one, or starting from a template
The structure of a silica plan is much the same from job to job, because the regulations set out what it has to address. What changes is your work, your materials, your controls and your people. That is the case for starting from a built plan and completing it, the same argument as for a SWMS template, and it carries the same warning: a plan that is downloaded and never completed is worse than none, because it states arrangements the business is not keeping.
Our Silica Risk Control Plan is an editable Word template written for your state, with the sections and appendices set out and the standard content drafted, ready for the project detail to be completed by someone competent. It is a template, not advice, and it does not make a business compliant on its own.
Start from a proper SWMS, not a blank page
State-specific, editable templates written for your state. Download instantly, then make it yours for the job and the site.
This guide is general information, not legal or safety advice, and does not guarantee compliance. Laws and site conditions vary, so always check your state regulator and have documents reviewed by a competent person.
