In Queensland, a Safe Work Method Statement (SWMS) must be prepared before high risk construction work starts, under section 299 of the Work Health and Safety Regulation 2011 (Qld). The business doing the work prepares it, follows it, gives a copy to the principal contractor on a construction project, reviews it and keeps it. The law does not require signatures.
Queensland follows the national model laws for SWMS, with a few local differences that matter on site, mostly around falls. This page covers the Queensland rules. To compare states, see the hub: SWMS requirements by state.
Which law applies in Queensland?
- The Act: the Work Health and Safety Act 2011 (Qld).
- The Regulation: the Work Health and Safety Regulation 2011 (Qld). The SWMS rules are in Chapter 6 (construction work), sections 291 and 299 to 303.
- The regulator: Workplace Health and Safety Queensland (WHSQ), at worksafe.qld.gov.au.
Note that Queensland's Regulation numbers its provisions as "sections", where the model regulations use "regulations". The numbers line up for the SWMS rules.
When is a SWMS required in Queensland?
A SWMS is required before any high risk construction work (HRCW) starts. Section 291 of the Regulation defines high risk construction work as construction work that, among other things:
- involves a risk of a person falling more than 2 metres
- is carried out on a telecommunication tower
- involves demolition of a load-bearing element, or the disturbance of asbestos
- involves structural alterations or repairs that require temporary support to prevent collapse
- is carried out in or near a confined space, or a shaft or trench deeper than 1.5 metres, or a tunnel
- involves the use of explosives, tilt-up or precast concrete, or diving work
- is carried out on or near pressurised gas mains, chemical, fuel or refrigerant lines, or energised electrical installations or services
- is carried out in an area that may have a contaminated or flammable atmosphere, or artificial extremes of temperature, or near water with a risk of drowning
- is carried out on, in or next to a road, railway, shipping lane or other traffic corridor in use, or where there is any movement of powered mobile plant.
That is the same list of 18 categories as the model regulations. For examples of each, see high risk construction work: the 18 categories.
What must a Queensland SWMS contain?
Section 299(2) says a SWMS must:
- identify the work that is high risk construction work
- state the hazards relating to that work and the risks to health and safety associated with those hazards
- describe the measures to be implemented to control the risks
- describe how the control measures are to be implemented, monitored and reviewed.
Section 299(3) adds that it must be prepared taking into account the circumstances at the workplace and, on a construction project, the WHS management plan, and that it must be set out and expressed in a way that is readily accessible and understandable to the people who use it.
WHSQ's guidance says a SWMS should also include:
- the business's name, address and Australian Business Number (ABN), if it has one
- the people responsible for making sure the SWMS is implemented, monitored and complied with
- on a construction project, the principal contractor's name, the address of the work, the date the SWMS was prepared and the date it was given to the principal contractor, and the review date (if any).
WHSQ also says the content should give clear direction, with no statements that leave a decision to supervisors or workers. Its example: "use appropriate PPE" (personal protective equipment) does not detail the control measures.
The Queensland falls rule
This is the main local difference. Section 299(4) says that if a SWMS for work with a risk of a fall of more than 2 metres states that the only controls will be administrative controls or PPE, it must describe all the control measures that were considered in deciding which to use, including by addressing the general fall protection requirements in section 79(3).
Queensland also sets specific fall controls for construction work in Division 4 of Part 6.3 of the Regulation (sections 306A to 306Q), covering edge protection, travel restraint, fall arrest platforms, harness systems, safety nets, ladders, trestle platforms and scaffolding. WHSQ explains that these specific controls apply where there is a risk of a fall of at least 3 metres in housing construction work and at least 2 metres in other construction work. A SWMS is still required for any construction work with a risk of a fall of more than 2 metres, including housing.
In practice: if you are a housing trade in Queensland and your SWMS relies on ladders, training or a harness alone, read sections 299(4) and 306A to 306Q before you submit it.
Who prepares, keeps and signs a SWMS in Queensland?
Who prepares it. The business (the person conducting a business or undertaking, or PCBU) carrying out the high risk work must make sure a SWMS is prepared, or has already been prepared by another person, before the work starts (section 299(1)). WHSQ says the PCBU, in consultation with the workers doing the work, is best placed to prepare it.
Following it. The PCBU must have arrangements to make sure the work is done in line with the SWMS. If it is not, the work must stop immediately or as soon as it is safe to do so, and resume only in line with the SWMS (section 300).
The principal contractor. On a construction project, a copy must be given to the principal contractor before the high risk work starts (section 301). The principal contractor must take all reasonable steps to obtain it (section 312). In Queensland, a construction project is one where the cost of the construction work is $250,000 or more (section 292), and the principal contractor must prepare a written WHS management plan before work on the project starts (section 309). See principal contractor duties by state.
Review. The SWMS must be reviewed and, as necessary, revised if relevant control measures are revised (section 302).
Keeping it. A copy must be kept until the high risk work is completed, or for at least 2 years after a notifiable incident connected with the work. While it must be kept, it must be readily accessible to the workers doing the work and available for inspection (section 303).
Signatures. None of these sections requires anyone to sign the SWMS. WHSQ says a SWMS may include the names of workers consulted, the date of consultation, and each worker's signature acknowledging their participation. Many principal contractors make a signed sign-on a site rule, so expect to be asked. See keeping, signing and reviewing a SWMS.
Can I use a generic SWMS in Queensland?
Yes, with a condition. WHSQ says a generic SWMS may be prepared and used for work carried out regularly, but before each new activity it must be reviewed and revised to make sure it applies to the high risk work and the actual workplace. See master SWMS vs task SWMS.
Free SWMS template options in Queensland
- Safe Work Australia's interactive SWMS tool. WHSQ points to this free online tool (last updated 25 January 2024), which explains how to prepare, use and review a SWMS. Safe Work Australia says it is based on the model WHS laws and does not cover laws specific to your state or territory, so check the Queensland differences above.
- WHSQ's house relocation guide. For help developing a SWMS, WHSQ points to its guide Working safely in the house relocation industry (2015). In that guide, Appendix B is the guidance for filling out a SWMS and Appendix C is the blank SWMS template.
- Writing your own. You can write a SWMS from a blank page. See how to write your own SWMS and our guide to free SWMS templates in Australia.
A free template gives you the structure. The time goes into the content: the tasks, hazards and controls for your trade, written specifically enough to satisfy section 299 and the principal contractor.
Queensland editions of our packs
Our SWMS Trade Packs come in a Queensland edition. Choose QLD (Queensland) when you select your state. The Queensland edition references the Work Health and Safety Act 2011 and Queensland's regulator, in editable Word, with the tasks, hazards and controls drafted for your trade. You still need to add the site, the crew and the controls for the actual job, and have it reviewed by a competent person.
Common questions
Is a SWMS a legal requirement in Queensland?
Yes, for high risk construction work. Section 299 of the Work Health and Safety Regulation 2011 (Qld) requires a Safe Work Method Statement (SWMS) to be prepared before high risk construction work starts. Section 291 lists the 18 categories of high risk construction work.
Who has to sign a SWMS in Queensland?
The Queensland Regulation does not require a SWMS to be signed. Workplace Health and Safety Queensland says a SWMS may include workers' signatures acknowledging they were consulted. Many principal contractors require a crew sign-on as a site rule.
Is there a free SWMS template in Queensland?
Workplace Health and Safety Queensland points to Safe Work Australia's free interactive SWMS tool, and to its 2015 guide Working safely in the house relocation industry, where Appendix B explains how to fill out a SWMS and Appendix C is a blank SWMS template. Any template still has to be completed for the actual work and site.
How long do I keep a SWMS in Queensland?
Until the high risk construction work is completed, or for at least 2 years after a notifiable incident connected with that work. It must be accessible to workers and available for inspection during that time (section 303).
What is different about SWMS in Queensland?
The content rules match the model regulations, but Queensland adds section 299(4): if a SWMS for work with a fall risk over 2 metres relies only on administrative controls or personal protective equipment, it must describe all the controls that were considered. Queensland also sets specific fall controls, including for housing construction where a person could fall 3 metres or more.
Sources: Work Health and Safety Regulation 2011 (Qld), sections 79, 291, 292, 299 to 303, 306A to 306Q, 309 and 312, Work Health and Safety Act 2011 (Qld), Workplace Health and Safety Queensland, Safe work method statements, Workplace Health and Safety Queensland, Work at heights, Safe Work Australia, Interactive SWMS tool and Workplace Health and Safety Queensland, Working safely in the house relocation industry (2015).
Start from a proper SWMS, not a blank page
State-specific, editable templates written for your state. Download instantly, then make it yours for the job and the site.
This guide is general information, not legal or safety advice, and does not guarantee compliance. Laws and site conditions vary, so always check your state regulator and have documents reviewed by a competent person.
