You need a Safe Work Method Statement (SWMS) for roofing work that is high risk construction work (HRCW). Most roofing is: construction work with a risk of a person falling more than 2 metres is one of the categories, and roofing on all but the lowest single-storey buildings usually crosses that line. Old roofs can add asbestos, and work near overhead power lines or with deliveries by crane truck adds more categories.
The SWMS has to explain how falls are controlled, and the law sets the order: prevent the fall first, and only then rely on harnesses or administrative controls. This guide covers the categories, the falls rules and what the SWMS must say.
For the general test, see do I need a SWMS?. For the full list, see high risk construction work: the 18 categories.
When is roofing construction work?
Construction work includes work carried out in connection with the construction, alteration, renovation, repair, maintenance or refurbishment of a structure (regulation 289 of the model Work Health and Safety (WHS) Regulations; section 289 of Queensland's WHS Regulation 2011). New roofs, re-roofing, roof repairs and gutter replacement are usually construction work. Minor testing, maintenance or repair work on a structure is excluded (r 289(3)(d)), but the falls risk still has to be managed on any roof.
Which high risk construction work categories matter for roofing?
The model WHS Regulations list 18 categories in regulation 291 (section 291 in Queensland). The ones roofers hit most are construction work that:
- involves a risk of a person falling more than 2 metres
- involves, or is likely to involve, the disturbance of asbestos
- is carried out on or near energised electrical installations or services
- is carried out in an area at a workplace in which there is any movement of powered mobile plant, for example crane trucks lifting sheets onto the roof
- is carried out in or near a confined space, for example some roof spaces and ceiling voids, depending on the space.
Common roofing jobs and the categories they often trigger
This is a guide, not a ruling. The fall height, the roof surface and what is around the job decide which categories apply.
| Roofing task | Often triggers | Note |
|---|---|---|
| New sheet roofing | Falls over 2 m; powered mobile plant during lifts | Edge protection and safety mesh are common controls. |
| Tiled roofing | Falls over 2 m | Loading tiles onto the roof adds manual handling. |
| Re-roofing and roofing removal | Falls over 2 m; possibly asbestos | Brittle or fragile sheeting and skylights. |
| Gutters, fascia and downpipes | Falls over 2 m | Often done from a scaffold or elevating work platform. |
| Skylight and whirlybird installation | Falls over 2 m | Openings must be covered or protected. |
| Work in roof spaces | Possibly confined space; possibly energised electrical | Hidden cables, heat and ceiling joists. |
| Painting or coating asbestos cement roofs | Asbestos; falls over 2 m | High-pressure water and compressed air are prohibited on asbestos. |
| Anchor point and static line installation | Falls over 2 m | Installers work before the anchors exist, so other fall controls are needed. |
| Roofing near overhead power lines | Energised electrical installations or services | Approach distances come from your regulator and the network operator. |
The falls rules roofers need to know
Model WHS Regulations. A person conducting a business or undertaking (PCBU) must manage risks from falls (regulation 78). If it is not reasonably practicable to eliminate the risk by doing the work on the ground or on a solid construction, the PCBU must minimise it by providing a fall prevention device, such as edge protection, a working platform or a cover over an opening; if that is not reasonably practicable, a work positioning system; and if that is not reasonably practicable, a fall arrest system (regulation 79). If a fall arrest system is used, the PCBU must establish emergency and rescue procedures (regulation 80). Sections 78 to 80 in Queensland match.
Queensland adds specific rules (sections 306B to 306Q of its WHS Regulation 2011). For housing construction work where a person could fall 3 metres or more, other construction work where a person could fall 2 metres or more, and any work on a roof with a slope over 26 degrees, the PCBU must use control measures to prevent a person falling any distance, or if prevention is not practicable, to arrest the fall (section 306D). For lower falls and flatter roofs, section 306C sets out its own steps. Section 306E sets requirements for edge protection.
Admin-only controls in a SWMS. In Queensland, if a SWMS for work with a risk of a fall of more than 2 metres says the only controls will be administrative controls or personal protective equipment (PPE), it must describe all the control measures that were considered (section 299(4)).
Safe Work Australia's model Codes of Practice Managing the risk of falls at workplaces and Managing the risk of falls in housing construction give practical guidance on edge protection, safety mesh, brittle roofs and harness systems.
What must a roofing SWMS cover?
Regulation 299 of the model WHS Regulations (section 299 in Queensland) says a SWMS must:
- identify the work that is high risk construction work
- state the hazards relating to that work and the risks to health and safety associated with those hazards
- describe the measures to be implemented to control the risks
- describe how the control measures are to be implemented, monitored and reviewed.
It must take into account the circumstances at the workplace and, on a construction project, the principal contractor's WHS management plan, and be readily accessible and understandable to the people who use it.
For roofing, that usually means the SWMS sets out:
- the fall controls for each edge, opening and fragile surface: edge protection, scaffold, safety mesh, covers or harness systems
- if harnesses are used, the anchor points, who checked them and the rescue plan
- how brittle or fragile roofing and skylights are identified and protected
- how materials are lifted and stored on the roof without overloading it or sliding off
- exclusion zones below for falling objects
- the asbestos status of the existing roof, where known, and what happens if suspected asbestos is found
- approach distances to overhead power lines
- heat, wind and wet-surface conditions that stop work
- who supervises and how the controls will be checked.
Workplace Health and Safety Queensland (WHSQ) says statements such as "use appropriate PPE" do not detail the control measures. Name the control you will use.
Asbestos roofs
Many older roofs and eaves contain asbestos cement sheeting. Work that is likely to disturb asbestos is high risk construction work. A PCBU must not use high-pressure water spray or compressed air on asbestos or asbestos-containing material (ACM), and power tools and brooms may only be used in controlled ways (regulation 446 of the model WHS Regulations; section 446 in Queensland). Removal of more than 10 square metres of non-friable asbestos needs a licensed asbestos removalist (regulation 458). See asbestos removal: SWMS and licences.
From 1 December 2026, workplace exposure limits (WEL) replace the workplace exposure standards (WES), including for airborne asbestos fibres. Safe Work Australia says PCBUs must comply with the WES list up to and including 30 November 2026, and with the WEL list from 1 December 2026. See what are WES and WEL?.
What is in the Roofing pack?
The Roofing SWMS Trade Pack has 20 SWMS: one Roofing Master SWMS and 19 task SWMS:
- Site Establishment & Setout
- Manual Handling
- Material Handling, Loading & Unloading
- Truck Operations & Deliveries
- Roof Edge Protection
- Roof Work (General)
- Sheet Roofing
- Tiled Roofing
- Roofing Removal
- Skylight & Whirlybird Installation
- Working in Roof Spaces
- Working at Heights - On Structure
- EWP Operations (elevating work platform)
- Working Near Overhead Power Lines
- Painting Asbestos Roofs
- Hazardous Substances
- Working in Private Residences
- Heat Stress
- Anchor Point and Static Line Installation
The pack comes in editable Word with a free pack of 17 safe operating procedures (SOPs). Each state edition references that state's Act and regulator. The pack does not include an asbestos removal licence or an asbestos removal control plan; removal over 10 square metres of non-friable asbestos needs a licensed removalist.
What still has to be tailored?
Before the SWMS goes to site, add:
- the site, the builder and the date
- the roof type, pitch and height, and any fragile or brittle areas
- the fall controls chosen for this roof and why higher controls were not practicable, where you use harnesses or admin controls
- the anchor points and the rescue plan, if harnesses are used
- the asbestos status of the roof, where known
- the overhead power lines and the approach distances that apply
- the crew, who supervises, and the crew's sign-on after you have talked it through with them.
See how to use a SWMS template and keeping, signing and reviewing a SWMS.
Victoria and other states
Victoria uses the Occupational Health and Safety (OHS) Regulations 2017, made under the OHS Act 2004. Construction work with a risk of a person falling more than 2 metres is high risk construction work (regulation 322). The falls rules in Part 3.3 apply to falls of more than 2 metres and set the order of controls: eliminate the risk, then a passive fall prevention device, then a work positioning system, then a fall arrest system, and only then a fixed or portable ladder or administrative controls (regulation 44). If only an administrative control is used, the employer must record the control and the task before the task starts (regulation 46), and emergency procedures including rescue must be set up before the task when controls other than elimination are used (regulation 49). Falls of 2 metres or less are covered by the employer's general duty under section 21 of the OHS Act 2004.
The other states and territories have adopted the model WHS Regulations in their own laws. See SWMS requirements by state.
Common questions
Does roofing work need a SWMS?
Usually. Roofing work with a risk of a person falling more than 2 metres is high risk construction work and needs a Safe Work Method Statement (SWMS) before it starts. Work that may disturb asbestos or is near overhead power lines also needs one.
Is a harness enough on a roof?
Not as a first choice. Under the model WHS Regulations, fall prevention such as edge protection, working platforms or covers comes before work positioning and fall arrest systems. If a harness is used, there must be emergency and rescue procedures.
What are Queensland's roof slope rules?
Queensland's WHS Regulation 2011 has extra falls rules for construction. For work on a roof with a slope over 26 degrees, housing work with a fall of 3 metres or more, or other work with a fall of 2 metres or more, controls must prevent a fall, or if that is not practicable, arrest it (section 306D).
Can I paint an asbestos roof?
Work likely to disturb asbestos is high risk construction work and needs a SWMS. High-pressure water spray and compressed air must not be used on asbestos, and power tools and brooms may only be used in controlled ways. Check your regulator's guidance before cleaning or coating an asbestos roof.
Is the list different in Victoria?
Victoria uses its own OHS Regulations 2017. Work with a risk of a fall of more than 2 metres is high risk construction work there too, and Part 3.3 sets Victoria's own order of fall controls and record rules for administrative controls.
Sources: Work Health and Safety Regulation 2011 (Qld), sections 78 to 80, 289, 291, 299 (including 299(4)), 306C, 306D, 306E, 446 and 458, Model WHS Regulations numbering, Safe Work Australia, Model Code of Practice, Occupational Health and Safety Regulations 2017 (Vic), Authorised Version No. 018 (as at 20 October 2026), regulations 41, 44, 46, 49 and 322, Occupational Health and Safety Act 2004 (Vic), section 21, Safe Work Australia, Workplace Exposure Limits for airborne contaminants and Workplace Health and Safety Queensland, Safe work method statements.
Start from a proper SWMS, not a blank page
State-specific, editable templates written for your state. Download instantly, then make it yours for the job and the site.
This guide is general information, not legal or safety advice, and does not guarantee compliance. Laws and site conditions vary, so always check your state regulator and have documents reviewed by a competent person.
