Free guide

Bricklaying and blocklaying SWMS: which tasks need one and what it must cover

Last reviewed:

You need a Safe Work Method Statement (SWMS) for bricklaying or blocklaying work that is high risk construction work (HRCW). The categories that come up most are a risk of falling more than 2 metres from scaffold or the structure, moving powered mobile plant such as telehandlers and forklifts, work near trenches deeper than 1.5 metres, and structural work that needs temporary support.

Dust from cutting bricks and blocks is not one of the 18 model categories, but it can bring in the crystalline silica rules, which sit beside the SWMS. In the ACT it goes further: processing crystalline silica material, such as brick, block or mortar, with a power tool is itself high risk construction work. This guide matches common bricklaying tasks to the categories, then covers what the SWMS must say and what else the job may need.

For the general test, see do I need a SWMS?. For the full list, see high risk construction work: the 18 categories.

Which high risk construction work categories matter for bricklaying?

The model Work Health and Safety (WHS) Regulations list 18 categories of high risk construction work in regulation 291. New South Wales, Queensland, Western Australia, South Australia and Tasmania use the same number and the same list. The Northern Territory and the ACT also use 291 with one change each, and Victoria has its own list (see Victoria and other states below). The ones bricklayers and blocklayers hit most are construction work that:

One SWMS can cover several categories, as long as it covers all of the high risk construction work in the task. Workplace Health and Safety Queensland (WHSQ) notes that where separate SWMS are prepared for different types of high risk work at the same workplace, you need to consider how the activities affect each other.

Common bricklaying jobs and the categories they often trigger

This is a guide, not a ruling. Whether a category applies depends on the height of the work, the scaffold, the excavations nearby and the plant on site.

Common bricklaying jobs and the categories they often trigger
Bricklaying taskOften triggersNote
Laying on upper floors or from scaffoldFalls over 2 mThe scaffold itself needs to be complete, inspected and handed over before use.
Laying from trestles or a mobile scaffoldFalls over 2 m once the platform height and open edges allow itCheck the actual fall height, including into excavations beside the wall.
Pallet deliveries by telehandler, forklift or truck cranePowered mobile plantExclusion zones and a set unloading area are the usual controls.
Retaining walls beside excavationsTrench or excavation over 1.5 m; powered mobile plant; fallsThe excavation and its support belong in the method, not just the wall.
Building against or near a cut batterTrench or excavation over 1.5 mGround conditions and who has checked the batter matter.
Brick replacement, lintels or openings in existing wallsStructural alterations needing temporary support; load-bearing demolitionPropping to an engineer's or builder's instructions.
Brick cleaning and repointingFalls over 2 m if done at heightAcid and chemical handling sit in the hazardous substances controls.
Work near overhead power lines or in occupied buildingsEnergised electrical installations; possibly asbestosApproach distances come from your regulator and the network operator.
Ground-level garden walls and low workOften noneA builder can still ask for a SWMS as a site rule.

Two things the table does not change. A builder or principal contractor can ask for a SWMS for work that is not high risk construction work. And work outside the categories, such as manual handling of blocks, still has to be managed safely.

What must a bricklaying SWMS cover?

Regulation 299 of the model WHS Regulations (299 in every state and territory except Victoria) says a SWMS must:

  1. identify the work that is high risk construction work
  2. state the hazards relating to that work and the risks to health and safety associated with those hazards
  3. describe the measures to be implemented to control the risks
  4. describe how the control measures are to be implemented, monitored and reviewed.

It must take into account the circumstances at the workplace and, on a construction project, the principal contractor's WHS management plan. It must be readily accessible and understandable to the people who use it.

For bricklaying, that usually means the SWMS sets out:

Workplace Health and Safety Queensland says statements such as "use appropriate PPE" (personal protective equipment) do not detail the control measures. WorkSafe Victoria says a SWMS should not list many control options to choose from. Name the control you will use.

What sits beside the bricklaying SWMS?

Scaffold and licences. The WHS Regulations define scaffolding work as erecting, altering or dismantling a temporary structure that supports a platform and from which a person or object could fall more than 4 metres, and list the scaffolding licence classes in schedule 3. Regulation 225 says suspended, cantilevered, spur and hung scaffolds, and any other scaffold from which a person or thing could fall more than 4 metres, must not be used until a competent person confirms in writing that construction of the scaffold is complete. Every state and territory except Victoria uses the same definition and the same regulation number. Victoria has its own scaffolding and licensing rules under the OHS Regulations 2017. Bricklayers working from a scaffold are not erecting it, but nobody on the crew should be altering it without the right licence where one applies.

Silica. Cutting, grinding and chasing masonry can release respirable crystalline silica. Safe Work Australia's crystalline silica code of practice lists bricks, blocks, mortar, and brick or concrete cutting and grinding as sources of respirable crystalline silica. Under Chapter 8A of the model WHS Regulations, where the processing of a crystalline silica substance is high risk, a silica risk control plan must be prepared before the processing starts (regulation 529CB). New South Wales, Queensland, Western Australia, South Australia, Tasmania and the Northern Territory use the same regulation number. Where the processing is also high risk construction work, a SWMS that covers everything the plan must include can be used instead (regulation 529CB(3)). Victoria requires a crystalline silica hazard control statement for high risk crystalline silica work under its OHS Regulations 2017. The ACT's silica rules are in Chapter 7A of its WHS Regulation 2011, and there processing crystalline silica material with a power tool is high risk construction work, so it needs a SWMS. Check the rule that applies at the site. See what is a silica risk control plan?.

Manual handling. Blocks, bricks and mortar are heavy and repetitive. Manual handling is not a high risk construction work category, so it does not have to be in the SWMS, but it still has to be managed. WorkSafe Victoria makes the same point about non-HRCW hazards: they must still be managed, even if they are not in the SWMS.

Plant procedures. The brick saw, angle grinder and mixer are better covered by safe operating procedures (SOPs) beside the SWMS.

What is in the Bricklaying pack?

The Bricklaying SWMS Trade Pack has 13 SWMS: one Bricklaying Master SWMS and 12 task SWMS:

The pack is $249.99 per state, in editable Word, and comes with a free pack of 12 safe operating procedures (SOPs), including the brick saw (wet masonry saw), angle grinder, portable concrete mixer and high pressure washer. Each state edition references that state's Act and regulator.

If you are also asked for your safety system, the Bricklaying All-In WHS Pack puts the same SWMS inside the policies, procedures, registers and forms for the business.

What still has to be tailored?

Before the SWMS goes to site, add:

See what to do after you download your SWMS pack, and keeping, signing and reviewing a SWMS.

Victoria and other states

Victoria lists 19 types of high risk construction work under its own Occupational Health and Safety (OHS) Regulations 2017, made under the OHS Act 2004. They are similar to the model list but worded separately, so use WorkSafe Victoria's list for work there. The other states and territories have adopted the model WHS Regulations in their own laws, with two differences worth knowing. In the Northern Territory, the falls category for residential construction work (Class 1 houses, and Class 10 buildings such as garages, carports and sheds attached or next to them) applies where a person could fall more than 3 metres; the 2 metre threshold applies to other construction work. In the ACT, section 291 adds a 19th category: processing crystalline silica material using a power tool or another mechanical method. In the ACT, that means cutting, grinding or chasing brick, block or concrete with a power tool is high risk construction work. See SWMS requirements by state.

Common questions

Does bricklaying need a SWMS?

Bricklaying needs a Safe Work Method Statement (SWMS) when the work is high risk construction work, such as laying from scaffold where a person could fall more than 2 metres, working where telehandlers or forklifts are moving, or building retaining walls beside excavations deeper than 1.5 metres. Low ground-level work may be outside the categories, though builders often ask for a SWMS anyway.

Do I need a SWMS for working on scaffold?

If a person could fall more than 2 metres from the scaffold or the structure, the work is high risk construction work and needs a SWMS. Erecting, altering or dismantling scaffold from which a person or object could fall more than 4 metres is scaffolding work, which needs the right high risk work licence.

Is silica dust covered by the SWMS?

Outside the ACT, cutting bricks and blocks is not itself a high risk construction work category, but the dust controls belong in the SWMS for the task. Where processing a crystalline silica substance is high risk, the WHS Regulations also require a silica risk control plan before the work starts, and a SWMS that covers the same content can be used instead. In the ACT, processing crystalline silica material with a power tool is itself high risk construction work. Victoria uses a crystalline silica hazard control statement.

Do retaining walls need a SWMS?

Often yes. Retaining walls are usually built beside excavations and with plant moving nearby, so the trench or excavation category and the powered mobile plant category can both apply. The SWMS should cover the excavation and its support, not only the wall.

Is the list different in Victoria or other states?

Victoria uses its own Occupational Health and Safety (OHS) Regulations 2017 and lists 19 types of high risk construction work. The categories are similar but worded separately, so check WorkSafe Victoria's list for work in Victoria. Two other places differ from the model list: in the Northern Territory the falls category for houses and their garages and sheds starts at more than 3 metres, and the ACT adds processing crystalline silica material with a power tool or other mechanical method as a 19th category.

Sources: Model WHS Regulations (Safe Work Australia), regulations 5, 225, 291, 299 and 529CB and schedule 3; the WHS Regulations of NSW, Queensland, WA, SA, Tasmania, the ACT (sections 291 and 418A) and the NT (regulation 291); Victoria's OHS Regulations 2017; WorkSafe Victoria; Workplace Health and Safety Queensland; Safe Work Australia's crystalline silica code of practice.

Start from a proper SWMS, not a blank page

State-specific, editable templates written for your state. Download instantly, then make it yours for the job and the site.

This guide is general information, not legal or safety advice, and does not guarantee compliance. Laws and site conditions vary, so always check your state regulator and have documents reviewed by a competent person.